Baumatic BT06.7ME User Manual

BT06.8ME BT08.8ME 60 cm Integrated hood

10Using your Baumatic cooker hood Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o

11Speed control slider 0 = Off 1 = Low speed 2 = Medium speed 3 = High speed o The cooker hood can be operated by leaving the speed control s

12Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH

13Maintenance Removing and changing the grease filter o Locate the two catches at the base of the filter as shown in the diagram a

14 o Remove the metal wires which hold the synthetic filter in place. o Remove the synthetic filter and replace with

15Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MA

16o Once the bulb has been replaced, refit the panel by screwing the screws back into place. Fitting the carbon filter If the appliance is going

17o Ensure the filter unclips from the hood, as shown in the diagram on the previous page, before you pull it away. This will allow you access to th

18Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicate

19o The brown wire must be connected to the terminal marked “L” (live), or coloured red. Before beginning installation o Check th

2User Manual for your Baumatic BT06.8ME/BT08.8ME 60 cm Integrated hood NOTE: This User Instruction Manual contains important in

20o Select a flat surface for assembling the cooker hood. Cover that surface with a protective covering and place all cooker hood parts and fittings

21o Remove the filter by locating the two catches at the base of the filter as shown in the diagram on the previous page (1). o Insert a finger in

22o Hang the cooker hood onto the screws between the two cupboards. o Push the fan-shaped door frames to the end (f

23Fitting the décor door o The décor door should be no less than 16 mm thick, 385 – 700 mm high and weigh no more than 7 kg. o P

24o Place the décor door on a protective surface to avoid damage. Mark the installation position of the door frame and the size of the fixed screws

25 o Install the adjusting plate, in order to cover the gap between the wall and the bottom of the cooker hood, by screwing it into place. Conne

26o Fit a suitable ducting terminal (not supplied) to the wall and connect a 125 mm ducting hose (not supplied) to the terminal. Genuine spare parts

27The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. The appl

28o Turn off the hob and then wait for the safety cut-out device to reset. o IMPORTANT: If you have installed your cooker hood too low, the safety

29Baumatic Consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwashers (200 g) o BC003 Ceramic

3Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood 8 – 9 BT06.8ME

30 United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales

31

32

4ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug usel

5IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before a

6o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLE

7o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observ

8Specifications of your cooker hood BT06.8ME Dimensions: Height: 395 mm Width: 600 mm Depth: 282 mm Specifications: o 1 x Int

9BT08.8ME Dimensions: Height: 395 mm Width: 600 mm Depth: 282 mm Specifications: o Twin integrated axial motor o Slider co