sSpare parts list for Candy model Supplier model number:HJA26017119550m3/H1B20-2201-004-P Upper Chimney (400MM height)1USD 3.52B20-2201-006-P Lower C
o Note: Your cooker hood is designed to remove cooking odours from the room and not steam. o Warning - Always ensure that the cooker hood has been
Specifications of your cooker hood F60.2-BL/SS PRODUCT DIMENSIONS Height: 638–1080mm* Width: 600 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECT
F70.2-BL/SS PRODUCT DIMENSIONS Height: 638–1080mm* Width: 700 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 172 mm x 222 mm Your stai
F90.2-BL/SS PRODUCT DIMENSIONS Height: 638–1080mm* Width: 900 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 172 mm x 222 mm Your stainle
Optional extras (all models) DK5 1 Metre length Ducting Kit 125 mm Ø. DK10 3 Metre length Ducting Kit 125 mm Ø with flat channelling included. o A
o Find the control panel, which is located at the front right of the canopy. o There are several buttons on the control panel, which perform separa
The grease filters o Your cooker hood is fitted with grease filters, which help to absorb grease particles and protect your kitchen and furniture fr
Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS
15itting the carbon filters filters. This will help to absorb unpleasant odours caused by cooking. THE ) Remove the grease filters. the centre f
16nstallation I IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicate
BaumaticSpare parts list for Baumatic model F60.2SS-ARPosition PrefixSupplierItem codeMODEL NUMBERDescription UK Currency Price1 XAA B20-2201-004-P F6
o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured markings identifying the terminals in your spur box,
o Do not tile, grout or silicone this appliance to the wall. This appliance is designed to be surface mounted only. Installing your cooker hood I
2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 19 3) Using a
6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the
Connecting to external ducting Important: To get the optimum performance from your appliance, 150mm ducting should be used. 8) Connect a 150 mm du
10) Lift chimney section (D) upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the
12) Using a 6 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and
Completing the installation o If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitti
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Baumatic Customer Care Department, please
IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact Baumatic Cus
27 United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 690
28
F60.2-BL/SS F70.2-BL/SS F90.2-BL/SS Cooker hood
User Manual for your Baumatic F60.2-BL/SS 60 cm cooker hood F70.2-BL/SS 70 cm cooker hood F90.2-BL/SS 90 cm cooker hood
3Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood 8 – 11 F60.2-BL/SS
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useles
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before att
o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN
Comments to this Manuals