Baumatic BES900BGL User Manual

my BES900BGL 90 cm Glass Chimney Hood

o It is highly recommended that the hood lights are only used when the appliance is in operation. They should not be used as a permanent lighting sou

o When the display shows the correct countdown time, release all buttons and in a few seconds the countdown will begin. o When the countdown time

Maintenance Removing and cleaning the grease filters o First lift up the cover screen and then remove the grease filters by pull

o Repeat the process if required. o Refit the grease filters once they have dried and close the cover screen. o IMPORTANT: Let the grease filter

o IMPORTANT: It is not possible to replace the bulbs individually, it will be necessary to obtain the bulbs, bulb holders and wiring as a complete pa

2) Hook the carbon filter over the pins that are located at the end of the motor. 3) Turn the carbon filter clockwise, until you feel it click

Electrical connection 16 YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION. o The cooker hood’s power cable must be fitted upstre

17o Ensure that all electrical connections are carried out by a suitably qualified person. o Before commencing installation of the cooker hood the

Extraction mode or recirculation mode? IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR

IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED. 191) Remove the

User Manual for your Baumatic BES900BGL 90 cm Glass Chimney hood NOTE: This User Instruction Manual contains important information, including

2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 3) Using a drill bit

6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) thro

Connecting to external ducting 8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (pleas

10) Lift chimney section (D) upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the

12) Using an 8 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and

Completing the installation o If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitti

o If the hood is set up for extraction mode, check that the ducting hose and discharge outlet are not blocked. My cooker hood has switched off duri

27Baumatic Consumables o BC001 Degreaser for Dishwashers (200g) o BC002 Descaler for Washing Machines and Dishwashers (200g) o BC003 Ceramic H

United Kingdom Baumatic Ltd., Baumatic Buildings, Czech Republic 6 Bennet Road, Baumatic CR spol s.r.o. Reading, Berkshire Lípovà 665 RG2 0Q

29

3Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood 8 – 9 Product dimens

30

31

ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useles

IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before att

o When installed between adjoining wall cabinets, the cabinets must not overhang the hob. o The edges of the cooker hood are sharp – be mindful of t

to observe the fire safety advice contained in this instruction booklet. o Remember that when in extraction mode, your cooker hood is removing air f

Specifications of your cooker hood PRODUCT DIMENSIONS Height: 650 mm Width: 900 mm Depth: 430 mm Your cooker hood is

Using your cooker hood o Make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s install