el 1BHG620SS / BHG690SS / BHG625SS / BHG695SS / BHG720SS / BHG725SS / BHG790SS Gas hobs
10HG720SS / BHG725SS / BHG790SS roduct dimensions: Aperture dimensions: Width: 560 mm eight: 40 mm Product specifications: wok) burner rs 1
11lectrical details Supply Connection: tched fused outlet with gap) ains Supply Lead: 3 core x 0.75mm² (Type RR-F <HAR> marked) as details
12HG625SS / BHG695SS triple crown (wok) B = 1.75 kW semi-rapid ary burner = Control panel HG720SS / BHG790SS crown semi-rapid auxiliary
13sing the gas hob U Before first use IMPORTANT: You should clean the hob surface (see symbols will appear on the control panel, next to each “Clean
o To switch the burner off, turn the control knob fully clockwise to the gas off position. o In case of power failure, the burners can be lit by ca
Cleaning Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before comme
o After cleaning and washing them, wipe and dry them carefully. o Before placing the burners back on the hob top, make sure that the gas jet is no
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is locat
o 50 mm clearance around the appliance and between the hob surface and any combustible materials. Unpacking the appliance When unpacking the applia
BHG625SS / BHG695SS BHG720SS / BHG725SS / BHG790SS o Cut a hole in the worktop that corresponds with the relevant drawing for you
User Manual for your Baumatic BHG620SS / BHG625SS / BHG690SS / BHG695SS 60 cm 4 Burner gas hob BHG720SS / BHG725SS / BHG790SS 70 cm 5 Burner gas h
All models o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it.
o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten
22Ventilation requirements o The room containing the hob should have an air supply in accordance with the current edition of BS 5440: Part 2: o
Gas Safety (Installation and Use) Regulations IMPORTANT: The appliance MUST be connected to the gas supply by use of a 15 mm x ½” female coupler, sea
Gas adjustment (Conversion to LPG) All work must be carried out by a GASSAFE registered engineer. IMPORTANT: Always isolate the hob from the electri
Minimum flow adjustment for hob gas taps. All work must be carried out by a GASSAFE registered engineer. IMPORTANT: Always isolate the hob from the
Gas tap maintenance These maintenance operations MUST ONLY be carried out by a GASSAFE registered engineer. IMPORTANT: Before carrying out any maint
Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in c
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your main
29Baumatic Consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwashers (200 g) o BC003 Ceramic
3Contents Environmental note 4 Important safety information 5 – 7 Specifications 8 – 13 BHG620SS / BHG690SS 8 BHG625SS / BHG
30
United Kingdom Czech Republic Baumatic Ltd., Baumatic CR spol s.r.o. Baumatic Buildings, Lípovà 665 6 Bennet Road, 460 01 Liberec 4 Reading, B
32
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. all packaging mater
5Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before at
6hild Safety ce at any time. During and after use, all surfaces will be hot. se ensure that they are kept under close supervision at all times. uld o
7leaning Cleaning of the hob should be carried out on a regular basis. appliance, it should be disconnected from the mains and cool. using this ap
8pecifications S BHG6 Width: 560 mm rs o LPG conversion jets 20SS / BHG690SS Product dimensions: Aperture dimensions: Depth: 5
9HG625SS / BHG695SS roduct dimensions: Aperture dimensions: Width: 560 mm eight: 40 mm roduct specifications: urner rs 1 x 1.00 kW auxiliary
Comments to this Manuals