Baumatic PV372SS User Manual

ch PV372SS 35 cm Island cooker hood PV972GL 90 cm Glass island cooker hood

Optional extras (all models) S1 1 pair of carbon filters DK5 1 Metre length Ducting Kit 125 mm Ø. DK10 3 Metre length Ducting Kit 125 mm Ø with fla

o Before operating the hood, make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s inst

The grease filter o Your cooker hood is fitted with a grease filter, which helps to absorb grease particles and protect your kitchen & furniture

o Refit the grease filter once it has dried and then retighten the fixing screw that holds it in place. o IMPORTANT: Let the grease filt

o Use a screwdriver to remove the 6 fixing screws that hold the light board in place. o Prior to touching the light bulbs ensure that t

o Push the light back into the exposed hole in the hood and reconnect the light wiring point (see page 23 for a line drawing that shows h

Fitting the carbon filters If the appliance is being used to be used in recirculation mode then it is necessary to fit carbon filters. This will hel

o The carbon filters should be replaced approximately every three months, if they show signs of damage, or if you start to notice that cooking smells

Electrical connection YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION. o The cooker hood’s power cable must be fitted upstream

19Before beginning installation o Check that the product purchased is of a suitable size for the chosen installation area. In addition check whethe

User Manual for your Baumatic PV372SS 35 cm Island cooker hood PV972GL 90 cm Glass island cooker hood NOTE: This User Instructi

Positioning X = Height of the appliance A = Total height of the kitchen B = Height of the worktop C = Distance betwe

If you are using the appliance in recirculation mode, then PLEASE NOTE that some of the vent in the upper chimney section must be exposed. You will ha

Installing the glass canopy (PV972GL only) o Carefully turn the appliance upside down, so that the grease filter is pointing upwards to the ceilin

o Carefully lift the glass canopy towards the main body of the hood. o Carefully locate the glass canopy over the main body of the hoo

o Use a screwdriver to retighten the 6 fixing screws that hold the base of the cooker hood in position. o IMPORTANT: These screws MUST be fully tig

o The hanging plate should be securely fixed to the ceiling, using the 40 mm x ST6 screws (9 pcs) and wall plugs (IMPORTANT: See note regarding wall

4) Locate the holes on the top of the main body of the cooker hood that you fix the connector pieces and angle bars to. o The positions of th

5) Lift the main body of the cooker hood towards the hanging plate. o If you are going to be using the hood in extraction mode, you should feed th

Completing the installation o The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed ins

o Connect the spigot to the top of the cooker hood, and then connect a 125 mm ducting hose to the spigot (please note that the ducting hose is not su

3Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood 8 – 10 PV372SS

My cooker hood has switched off during operation. o The safety cut-out device has been tripped. o Turn off the hob and then wait for the safety

31 United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales

32 32

ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useles

IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before att

o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN

o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed

Specifications of your cooker hood PV372SS PRODUCT DIMENSIONS Height: 875 - 1100 mm* Width: Ø 350 mm Depth: Ø 350 mm Your stainl

PV972GL PRODUCT DIMENSIONS Height: 875 mm -1100 mm* Width: 900 mm Depth: 600 mm 9 Your stainless steel cooker hood is fitted with: