BWD1212 Fully integrated washer dryer
10Spin selection button o Press this button to select the spin speed that you require for a particular wash program. Delay start button o Press
Detergent drawer 1) Pre wash section This compartment should have detergent placed in, if you are going to select a wash pro
Preparing the wash cycle Preparing your garments for washing o Your washing should be sorted out, according to the fabric type and the wash care sy
A selection of wash care symbols o The wash care symbols should be used to help you to select the most suitable wash program. They will also help y
Detergents and conditioners The amount of detergent that you need to use in your appliance, will depend on o The degree of soiling. Lightly soiled
Program table On program 15, if the machine senses that the garments are very dry, it will skip automatically to the cooling off phase. The LCD will u
- Indicates that softener can be added if required. - Indicates that detergent MUST be added. - Indicates that detergent MUST not be added. W
17Selecting a wash program 9 Load your laundry and put detergent in the relevant compartment(s) of the soap drawer. 9 Close the porthole door fir
Selecting a separate drying program 9 Load your laundry and then close the porthole door firmly. o IMPORTANT: The maximum amount of clothing that
Cancelling a wash program 9 Press the Start/pause button whilst a wash program is in progress and the appliance will go into pause status. o Turn
USER MANUAL FOR YOUR BAUMATIC BWD1212 Fully integrated washer dryer NOTE: This User Instruction Manual contains importan
Spin selection button o If you press the spin selection button, then the spin speed will reduce downwards from the one selected automatically for a
21Extra rinse option button o If you press the extra rinse option button, the indicator neon above it will light. o If you select this option, an
Control panel and washer dryer cabinet. IMPORTANT: Do not use any abrasive cleaner or household polish on either the control panel or operating part
23The washer dryer drum The drum of your washer dryer is constructed from stainless steel. However if there are objects that can rust placed inside
24Err5 o Machine does not fill to the specified level within 8 minutes. 9 Check that the inlet hose is not kinked or blocked and that the water tap
If a fault code reappears after following the advice given above, you should turn the wash program selection knob to the off position. Disconnect the
26o If it is unstable then follow the “Positioning and levelling the appliance” section. Poor spin results o Clean the drain pump (see “Cleaning
Poor wash results My garments are looking grey and there are limescale deposits present in the drum of my washer dryer. o There is not enoug
Cleaning the drain pump filter IMPORTANT: Switch off your washer dryer and disconnect the plug from your mains supply. You should clean out the fi
29r p. o Remove the filter and rinse out the filter undethe ta o Remove any debris from the filter. o Remove any debris that is in the area o
3Contents Environmental note 4 Important safety information 5 - 6 Specifications 7 - 8 Description of the appliance 8 - 10 Contr
o The location of the three transit bolts are shown in the diagram opposite. o You should use a spanner to loosen and remove the top t
Positioning and levelling the appliance 9 Place the washer dryer on a solid and level floor surface. 9 DO NOT PLACE THE WASHER DRYER ON A CARPET.
o If you are fitting the optional décor strip (see below). You should take into account the height that this will add to the appliance, when adjustin
o When you are facing the rear of the appliance, you will see two water inlet valves next to each other. The cold water inlet valve is on the left h
9 IMPORTANT: There should be a filter sitting inside the end of the inlet hoses that connects to your mains water supply. The inlet hoses may leak if
Fitting the furniture door o Please refer to the building in template for instructions on how to fit your integrated appliance and connect the furni
Power supply 9 IMPORTANT: As your appliance is a built in product, the electrical socket must still be accessible once the appliance is installed.
Before first use maintenance wash o When your washer dryer has been correctly installed, we recommend that you perform a maintenance wash cycle. o
38 United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales
39
Environmental note Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useles
40
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before atte
6o Before the first use of the appliance, we advise that the intense 90°C wash program is completed. No garments should be placed inside the machine
Specifications Product and aperture dimensions Appliance dimensions Aperture dimensions Height: 825 mm 868 mm (excluding décor strip)
Energy efficiency Energy rating (wash) A Energy rating (drying) C Wash performance A Water extraction performa
Control panel A Wash program selection knob B Start/pause button C Temperature selection button D Spin selection button E Delay start button F
Comments to this Manuals